Ubiquiti UniFi Protect G3 Flex Camera Pendant Mount (UVC-G3-F-PENDANT)
Upside-down mounting capability
Supports 1.5″—11.5 NPS and 3/4″ NPS
Compatible with the G3 Flex and G5 Flex
Sold as a single unit or 3-pack
Ubiquiti UniFi Protect G3 Flex Camera Pendant Mount (UVC-G3-F-PENDANT) Features
The UVC-G3-F-PENDANT-3 is a 3 pack of the Pendant Mount accessories for the UniFi Protect UVC-G3-Flex Cameras. The UVC-G3-F-Pendant allows you to suspend your UVC-G3-Flex camera from the ceiling using standard 1.5″-11.5 NPS or 3/4″-14 NPS threaded conduit*. The ethernet cable runs through the conduit to the camera in order to maintain a clean installation.
Features:
- Supports both 1.5″-11.5 NPS and 3/4″ conduit*
- 14 NPS threaded conduit
- Ethernet cable runs up through conduit for clean install
- Includes two screws for securing G3-FLEX to mount
Suspend your UVC-G3-FLEX camera from the ceiling with the pendant mount accessory. Works with standard 1.5″-11.5 NPS or 3/4″-14 NPS threaded conduit. The ethernet cable runs through the conduit for a clean installation. Includes two screws to secure the G3-FLEX camera into the mount.
Specifications
| UVC-G3-FLEX | |
| Dimensions | Ø 107.5 x 48 x 48 mm (Ø 4.23 x 1.89 x 1.89″) |
|---|---|
| Weight | 170 g (5.99 oz) |
| Sensor | 1/2.7″ 2-Megapixel HDR Sensor |
| Lens | EFL 4mm / f2.0 |
| Viewing Angle with Lens Distortion Correction (LDC) | |
| LDC Off | 87.4° (H), 47° (V), 104° (D) |
| LDC On | 80° (H), 46° (V), 92° (D) |
| Night Mode | IR LEDs with Mechanical ICR Filter |
| Video Compression | H.264 |
| Resolution | 1080p FHD (1920 x 1080) |
| Maximum Frame Rate | 25 FPS |
| Image Settings | Brightness, Contrast, Sharpness, Saturation, Noise Reduction, 50/60 Hz |
| Microphone | Yes |
| Management Interface | UniFi Protect |
| Networking Interface | (1) 10/100 Ethernet Port |
| Max. Power Consumption | 4W |
| Power Method | 802.3af PoE |
| Power Supply | 802.3af PoE Switch Port |
| Mounting | Table, Wall (Indoor/Outdoor), Pole |
| Operating Temperature | -20 to 50° C (-4 to 122° F) |
| Operating Humidity | 20 to 90% Noncondensing |
Installation
The UVC G3 Flex can be installed using one of the following methods:
- Desktop For installing on a flat surface such as a desktop or table/shelf; could be set up for temporary installations.
- Wall/Ceiling For installing in a secure location; used more for stationary or permanent installations.
- Pole For installing on a pole (indoor or outdoor).
Proceed to the appropriate section for your installation.
 | Note: The viewing angle or surveillance coverage of the G3 Flex camera can be changed at any time.
|
|---|
Be the first to review “Ubiquiti UniFi Protect G3 Flex Camera Pendant Mount (UVC-G3-F-PENDANT)”
Related products
Ubiquiti Accessories
Ubiquiti Accessories
Ubiquiti Accessories
Ubiquiti Accessories
Reviews
There are no reviews yet.